 |
Electronic Chemicals
|
PRODUCTS |
BESTCHEM DEBONDER
- For re-work reclaim jobs
- Reclaim you valuable parts with BESTCHEM DEBONDER. |
BESTCHEM MARKING INK CLEANERS
MODEL MIC-30
- Especially formulated to clean off stencil ink/ marking/ words on
PCB / ceramic, etc. |
BESTCHEM OCTOPUS LIQUID LEAK
DETECTOR
- Easily detect gas leaks in hard to reach areas. |
BESTCHEM SUPER DEIONISED WATER
- For cleaning electronics & components parts.
- Electronics Grade A
- Meet Military spec A-A-51367 |
BESTCHEM ISO PROPYL ALCOHOL
(2-PROPANOL) ISOPROPANOL
- Low mobile low MOS for electronics uses
- Meet Military spec MIL-F-5566 / TT-I-735A |
BESTCHEM METHANOL (METHYL
ALCOHOL)
- Low mobile Mos grade electronic.
- Meet military spec 0-M-232-E |
BESTCHEM HIGH QUALITY
SILICAGEL
- High capacity absorbent & desiccant amorphous form of silica.
- Excellent physical strength.
- Maximum resistances to fouling. |
BESTCHEM ACETONE
- Electronic grade
- Low mobile ion
- Semiconductor grade for MOS
- Meet military spec 0-A-51-G ASTM D329-81 |
ELECTRICAL PARTS CLEANER &
FLUX REMOVER
- Surface cleaning for PCB flux
- Non-flammable
- Non-ozone depleting
- Displaces moisture
- No CFC;S or HCFC’S |
BESTCHEM ULTIAMTE SOLUTION S-8
(R12)
Cleaning for:
- Flux
- Finger prints
- Grimes
- Oil
- Oxidations |
SC 1000 AQEOUS CLEANER
CONCENTRATE
- Cleans lab equipment/ hospital equipment/ food equipment/
Electronics products |
EZ ZAHN (ASTM) CUP VISCOSITY
CUPS
- Finest, most reliable, calibrated & documents cup in the market. |
TRITON SURFACTANTS
Triton X-100 Nonionic Surfactant |
|
KRYLON PRDUCT LIST | FOR : INDUSTRIAL MAINTENANCE CLEAR COATINGS
|
|
PART NUMBER |
PRODUCT |
PACKING |
| K1301 |
KRYLON ACRYLIC
CRYSTAL CLEAR
(MIL-TT-L-50) |
16 oz Can |
K1303
|
KRYLON CRYSTAL CLEAR
(MIL-TT-L-50) |
16 oz Can |
| K1305 |
KRYLON CRYSTAL CLEAR
U.V |
16 oz Can |
| K1402 |
KRYLON HIGH HEAT
ALUMINIUM PAINT |
16 oz Can |
| K1601 |
KRYLON GLOSS BLACK
17038 |
16 oz Can |
| K1602 |
KRYLON ULTRA FLAT
BLACK |
12 oz Can |
| K1614 |
KRYLON HIGH HEAT
BLACK |
16 oz Can |
| K1901 |
KRYLON REGAL BLUE |
16 oz Can |
| K2116 |
KRYLON SAFETY RED |
16 oz Can |
| All recommendations and
suggestions are made without guarantee since the conditions of use
are beyond our control |
TRI-FLOW PRODUCT LIST
| FOR: PREVENTIVE & CORRECTIVE MAINTENANCE
|
|
PART NUMBER |
PRODUCT |
PACKING |
| TF20027 (Aerosol) |
INDUSTRIAL LUBRICANTS
WITH TEFLON |
12 oz Can |
| TF26020 (Non-aerosol) |
INDUSTRIAL LUBRICANTS
WITH TEFLON |
1 Gallon |
| TF23004 (Tube) |
SYNTHETIC FOOD GRADE
GREASE H1 |
3 oz tube |
| TF22020 (Aerosol) |
SYNTHETIC FOOD GRADE
GREASE H1 |
16 oz Can |
| All recommendations and
suggestions are made without guarantee since the conditions of use
are beyond our control |
|
PRODUCTS |
DESCRIPTION |
PACKING |
|
Anti-Evaporation
Solvent Balls |
All-P Prevents excess loss of volatile solvents
due to evaporation. Also prevents the formation of toxic vapors and
heat evaporation/ |
In 1,000 pcs box |
|
Apron
 |
Provides protection & maintains
hygiene standards during food processing, metal
plating and fabricating & general cleaning works. |
|
|
Aspirator Bottle
 |
Furnished with screw-on caps to
contain liquids, solvents, oil etc. Small quantities can be drawn
through stopcocks. |
|
|
Thermometer
 |
Standard astm thermometers of
general purposes. Suitable for use in laboratories and plants or
general industries. |
|
|
Bestchem Anti-Rust Protector
(Converts Rust Into Primer)
 |
Converts rust into primer. It forms a bluish-gray
surface, can be painted over or slight sanding for a smoother
surface. Non- flammable.
APPLICATION:
It chips away loose rust, flaky paint & apply one coat of
bestchem anti-rust protector by brushing or spraying. Leave for 4-6
hours for the treated surface to turn into primer. |
4 litr container
20 ltrs container
|
|
Bestchem Absorbit
Compound
 |
Granular form, light weight. Excellent for
absorbing oil, acids & solvents spills. It can also be used as a
fire retardant.
APPLICATION:
Just sprinkle absorbit compound onto spillage. Let it absorb.
Sweep up and dispose off.
|
50 lbs bag
|
|
PRODUCTS |
DESCRIPTION |
PACKING |
|
Bestchem Anti-corrosion Tablet
(A vapour to protect metal
surface)
 |
Tablets that produce anti-corrosion vapour into
the surrounding air. Protects against salt & vapour.
APPLICATION:
By putting the tablets in any place in the carton boxes, containers,
computers, machines, tools equipment etc.
|
12 tables container
240 tables carton
|
|
Bestchem Heavy Duty anti-
Corrosion Polycoat C-80
 |
An
economical general purpose long-term protective poly coating against
rust, corrosion, oxidization in tropical humidity.
|
4 ltrs container
20 ltrs drum
200 ltrs drum
|
|
Bestchem FC-120
(A fluid coat on metal parts for up to 6 months)
|
Special product manufactured to coat internal parts of engine, spare
parts, tools precision machinery against corrosion, oxidization,
fungus & algae growth, rust on metal surfaces.
APPLICATION:
By soaking, wiping, brushing, dipping spraying on parts.
|
4 ltrs container
20 ltrs drum
200 ltrs drum
|
|
Safety Boots
 |
Steel-toe boots with complete waterproofing
properties & resistance to oil, acid & alkali with PVC tread.
|
|
|
Chemical Beakers, Funnels & Measuring Cylinder
 |
For measurements of fluid volumes, transferring &
containing chemical, etc. In the chemical industries, food
industries, refineries laboratories.
|
|
|
Chemical Plastic Pump
 |
For use in heavy & chemical industries to
dispense precise amounts of liquids from plastic containers or steel
drums. By manual transfer.
|
Available for:
20 ltr drum
200 ltr drum
|
|
PRODUCTS |
DESCRIPTION |
PACKING |
|
Chemical-Proof
Floor Mat
 |
Anti-skid, chemical-proof &
fireproof
|
|
|
Electrical Chemical
Pump
 |
For
use in heavy & chemical industries to dispense precise amounts of
liquids from plastic containers or steel drums. By electrical or air
compressor power.
|
|
|
Chemical Resistant
Floor Coating
|
Completely waterproof, chemical resistant & fireproof. Excellent for
applying on to cement mosaic & other types of surfaces.
|
|
|
Chemical Stirrer
 |
Steel-toe boots with complete waterproofing
properties & resistance to oil, acid & alkali with PVC tread.
|
|
|
Various Types of Containers
 |
To store non-poisonous chemicals or products such
as detergents. For general use in industries.
Various sizes & capacity available. |
|
|
Corrosive Sticker
 |
To be pasted outside carton box or cargo for
transportation, shipment, etc.
Various size available
|
|
|
Disposable gloves
 |
Soft & comfortable gloves for use in medical or
laboratory-based research, or even household chores to achieve the
highest standards of hygiene and safety.
|
|
|
PRODUCTS |
DESCRIPTION |
PACKING |
|
Drum Jack
 |
For moving, dumping, lifting, loading and
stacking of standard 44 gallon (200 litres drum).
|
|
|
Drum Opener
 |
For
opening either small or big caps used in standard 44-gallon (200
litres) drum.
|
|
|
Face shield
|
Face Protection.
|
|
|
Fire Extinguisher
 |
Essential equipment in firefighting. |
|
|
Flammable Sticker
 |
To be pasted outside carton box or cargo for
transportation, shipment, etc.
|
|
|
Hydrometers
 |
Used in checking the density of liquids,
temperature of chemicals in laboratories or any light or heavy
industries.
|
|
|
Oil absorbent
 |
For absorbing oil in spillages on land area.
|
50 pcs box
100 pcs bag
200 pcs bag
|
|
PRODUCTS |
DESCRIPTION |
PACKING |
|
Packaging Wrapping film
 |
For the packaging of wood products such as
furniture, food & beverages item, electronic products etc. With
anti-slip and cling properties.
|
|
|
Plastic Faucet
 |
Empties 55 gallon drums in less than 3 minutes. With instant on-off
control, which is unaffected by load. |
|
|
Poison Sticker
 |
To be pasted outside carton box or cargo for transportation,
shipment, etc.
Various sizes available.
|
|
|
Bestchem Epoxy &
Adhesive Remover EA-30
 |
A Specially formulated product with a powerful
debonding agent to break the tensile strength of the locitite or
other type of thread locking compound & epoxy.
APPLICATION:
Use a cotton bud to soak this liquid & apply on the threaded
locking compound which will soften & could clean away or
soak the parts to a quantity of bestchem epoxy & adhesive
remover EA-30 and let it dissolve by itself.
|
1 ltr btl
4 ltrs btl
20 ltrs drum
|
|
S00710 P.D.R.P Waxy
Film
 |
Features:
| + |
Penetrant/ Demoisturant/ Rust Preventive. |
| + |
Economical long-term outdoor rust
inhibitor. |
| + |
Protects against corrosion for up to 2
years under severe conditions ( Weather, salt water) |
| + |
Heavy, waxy film. |
| + |
Can be removed with mineral spirits. |
|
|
|
Thermax Paper
 |
Accurate method of determining surface
temperatures.
|
In 10 strips/ pkt
|
|
PRODUCTS |
DESCRIPTION |
PACKING |
|
Respirator & Mask
 |
Helps meet osha requirements for handling of
hazardous acidic vapors of concentrations up to 1,000 ppm.
.
|
|
|
Safety Cabinets
 |
Safety cabinets which can efficiently manage storage, transfer, use
and disposable of flammable liquid and other potentially hazardous
materials.
Various dimension available.
|
|
|
Safety Cans
 |
Fireproof and explosion-proof cans for permanent storage of
hazardous and flammable waste.
Various capacity available. |
|
|
Solvent Dispenser
 |
Dispenses volatile solvents into vessels of
smaller capacities.
|
Available in:
40z pc
60z pc
80z pc
|
|
Squeeze Bottle
 |
Round square shouldered bottle with swan neck jet
and screw closure. Natural polyethylene with alternative color coded
closure.
|
Available in:
250ml pc
500ml pc
1000ml pc
|
|
Tilting Drum Stand
|
A Special equipment used for moving, dumping,
lifting, loading & stacking of small & big drums, products or
equipments which are too bulky or heavy to carry manually/
 |
|
|
Ph Paper
|
Convenient testing of ph is buffer, acidic or
alkaline solution.
|
In 100 strips box
|
|
HumiSeal®
|
|
Range of Products:
- Widest selection of matrials to meet
electrical & environmental requirements
- Over 60 coatings, thinners, strippers and masking
materials
- Custom versions available
|
TempSeal TS300 |
TempSeal Application
|
|
TempSeal (HumiSeal TS300) is a
non-flammable, high temperature, temporary mask specially
designed and formulated to be used on printed circuit boards
that require masking during the conformal coating process.
TempSeal effectively covers and protects parts and
connections where coating is not desired. TempSeal can
remain on the board until ready for test. The mask is
removed by applying a mild peeling action. TempSeal contains
no ammonia and will not inhibit thermal cure silicone
conformal coatings. Since TempSeal can survive short
excursions to temperatures as high as 500°F, it can also be
used as a temporary solder masking material. |
 |
|
Strippers |
|
Humiseal 1063
A non-acidic, non-destructive, selective liquid strippers.
Dissolves all cured Humiseal polyurethane coatings without
most PC boards and components. Safe to use with copper,
gold, silver and nickel platings; amine cured epoxy; diallyl
phtalate; neoprene; phenolic; kynar; Teflon, poly-ethylene
and most vinyl coated wires.
Humiseal 1063 Gel
Similar to above but in gel form for partial, localised
removal of polyurethane film.
Humiseal 1072
Reactive solvent for dissolving polyether and polyester
urethanes such as Humiseal 1A20.
Humiseal 1076
Reactive solvent for dissolving polyether and polyester
urethanes such as Humiseal 1A20.
Humiseal 1080
VOC compliant. Dissolves all Humiseal Acrylic coatings.
Contains no ozone depleting chemicals. Meets EPA 33/50. Safe
for all PC boards.
Humiseal 1081
Contains no ozone depleting chemicals. Does not require
heating of either the printed circuit board assemblies or
the stripper to achieve maximum effectiveness. VOC
compliant.
Humiseal 1090
Effectively dissolves all Humiseal Silicone coatings.
|
|
Aerosol Coatings
|
|
A series of aerosols based on standard
Humiseal formulations but with a non-ozone depleting
propellant delivery system.
Humiseal 1B73
Fast drying, clear acrylic. Air dries to a hard, yet
flexible film. Cured coating may be soldered throught
leaving no residue.
Contains UV tracer. UL recognised. Qualified to
MIL-I-46058C.
Humiseal 1A33
Air cure, single component, clear polyurethane. Forms a
tough resilient film. UV tracer.
UL recognised. Qualified to MIL-I-46058C.
Humiseal 1A27
Air cure, single component, clear polyurethane. Forms a
tough resilient film. UL recognised.
Humiseal 1B31
Acrylic. Fast drying. An effective moisture sealant and
provides corrosion protection for various metal surfaces.
Humiseal 1H20AR1
Wtaer-based acrylic conformal coating. Provide excellent
moisture insulation resistance and can be chemically removed
or soldered through through for rework/
|
|
Humiseal® Waterbased Products
|
| HumiSeal Product |
1H20
AR1-D |
1H20
AR1-S |
1H20
AR2-D |
1H20
AR2-S |
1H20
UR5-D |
1H20
UR5-S |
1122
|
| Mil-I-46058CIPC-CC-830 |
YES |
YES |
YES |
YES |
YES |
YES |
NO |
| UL Recognized |
YES |
YES |
Pending |
Pending |
Pending |
Pending |
YES |
| Solids Content (% by weight) |
42 |
35 |
42 |
35 |
30 |
30 |
30 |
| Viscosity (centipoise) 2 |
1000 |
50 |
1000 |
50 |
250 |
50 |
3500 |
| VOC (grams/liter )3 |
<100 |
<50 |
<150 |
<150 |
65 |
65 |
412 |
| Tack Free Time
(minutes) 4 |
30 |
30 |
30 |
30 |
30 |
30 |
270 |
| Optical Brightener |
YES |
YES |
YES |
YES |
YES |
YES |
YES |
| Cure Type |
Elevated or Room Temperature |
Room
Plus HEAT |
HEAT |
| Shelf Life (months) |
12 |
12 |
12 |
12 |
12 |
12 |
12 |
| Operating Temp.
Range °C |
-65 to
+125 |
| IR (teraohms) 5 |
21 |
21 |
30 |
30 |
23 |
23 |
250 |
| MIR (gigaohms) 6 |
32 |
32 |
88 |
88 |
820 |
820 |
10 |
| Dielectric Constant
7 |
2.5 |
2.5 |
2.5 |
2.5 |
2.5 |
2.5 |
3.6 |
| Dissipation Factor
8 |
0.01 |
0.01 |
0.01 |
0.01 |
0.01 |
0.01 |
0.03 |
| Ease of Rework 9 |
Easy |
Moderate |
1 - Fed. Std. 141 Method 4044, 2 - Fed. Std. Method 4287
3 - Volatile Organic Compounds, 4 - Fed. Std. 141 Method
4061
5 - MIL-I-46058C, 6 - MIL-I-46058C
7 - ASTM D1 50 65T, 8 - ASTM D1 50 65T
9 - Very Easy = Can be easily removed by solvents or burn
through.
Easy = Not easily removed by solvents however can be removed
by Strippers, burn through or removed mechanically.
Moderate = Must be either mechanically removed or by using
special Strippers.
N/A = Coating not considered to be rework able.
DISCLAIMER: All values contained herein are typical
values. Please consult the Technical Data Sheet for the
specific product to obtain complete information and detailed
specification ranges and physical properties
|
|
Humiseal® Silicones Products |
| HUMISEAL PRODUCT |
1C49 |
1C49LV |
1C51 |
1C53 |
1C55 |
|
Mil-I-46058CIPC-CC-830 |
YES |
YES |
YES |
YES |
NO |
| UL Recognized |
YES |
YES |
YES |
YES |
NO |
| Solids Content (%
by weight)1 |
100 |
100 |
100 |
100 |
100 |
| Viscosity (centipoise) 2 |
7800 |
550 |
590 |
590 |
230 |
| VOC (grams/liter )3 |
0 |
0 |
0 |
0 |
0 |
| Tack Free Time
(minutes) 4 |
180 to
300 |
60 |
N/A |
N/A |
N/A |
| Optical Brightener |
YES |
YES |
YES |
YES |
YES |
| Cure Type |
Moisture |
Moisture |
HEAT |
HEAT |
HEAT |
| Shelf Life (months) |
6 |
6 |
6 |
6 |
6 |
| Operating Temp.
Range °C |
-65 to
+200 |
| IR (teraohms) 5 |
500 |
500 |
500 |
500 |
500 |
| MIR (gigaohms) 6 |
100 |
100 |
80 |
80 |
100 |
| Dielectric Constant
7 |
2.5 |
2.5 |
2.4 |
2.4 |
2.4 |
| Dissipation Factor
8 |
0.01 |
0.01 |
0.01 |
0.01 |
0.01 |
| Ease of Rework 9 |
Moderate |
1 - Fed. Std. 141 Method 4044, 2 - Fed. Std. Method 4287
3 - Volatile Organic Compounds, 4 - Fed. Std. 141 Method
4061
5 - MIL-I-46058C, 6 - MIL-I-46058C
7 - ASTM D1 50 65T, 8 - ASTM D1 50 65T
9 - Very Easy = Can be easily removed by solvents or burn
through.
Easy = Not easily removed by solvents however can be removed
by Strippers, burn through or removed mechanically.
Moderate = Must be either mechanically removed or by using
special Strippers.
N/A = Coating not considered to be rework able.
DISCLAIMER: All values contained herein are typical
values. Please consult the Technical Data Sheet for the
specific product to obtain complete information and detailed
specification ranges and physical properties
|
|
Humiseal® Urethanes Products
|
| HUMISEAL PRODUCT |
1A20 |
1A27 |
1A27LU |
1A33 |
1A34 |
2A64 |
|
Mil-I-46058CIPC-CC-830 |
YES |
NO |
NO |
YES |
YES |
YES |
| UL Recognized |
YES |
YES |
YES |
YES |
NO |
NO |
| Solids Content (%
by weight)1 |
50 |
50 |
50 |
44 |
39 |
55 |
| Viscosity (centipoise) 2 |
104 |
3750 |
3750 |
180 |
125 |
130 |
| VOC (grams/liter )3 |
511 |
4480 |
480 |
521 |
576 |
501 |
| Tack Free Time
(minutes) 4 |
60 |
30 |
30 |
15 |
140 |
N/A |
| Optical Brightener |
YES |
NO |
YES |
YES |
YES |
YES |
| Cure Type |
Moisture |
Oxygen |
Oxygen |
Oxygen |
Moisture |
Heat |
| Shelf Life (months) |
6 |
6 |
6 |
6 |
6 |
|
| Operating Temp.
Range °C |
-65 to
+125 |
| IR (teraohms) 5 |
300 |
200 |
200 |
200 |
170 |
450 |
| MIR (gigaohms) 6 |
48 |
12 |
12 |
16 |
63 |
48 |
| Dielectric Constant
7 |
3.5 |
3.6 |
3.6 |
3.6 |
3.5 |
3.5 |
| Dissipation Factor
8 |
0.028 |
0.02 |
0.02 |
0.03 |
0.028 |
0.024 |
| Ease of Rework 9 |
Moderate |
1 - Fed. Std. 141 Method 4044, 2 - Fed. Std. Method 4287
3 - Volatile Organic Compounds, 4 - Fed. Std. 141 Method
4061
5 - MIL-I-46058C, 6 - MIL-I-46058C
7 - ASTM D1 50 65T, 8 - ASTM D1 50 65T
9 - Very Easy = Can be easily removed by solvents or burn
through.
Easy = Not easily removed by solvents however can be removed
by Strippers, burn through or removed mechanically.
Moderate = Must be either mechanically removed or by using
special Strippers.
N/A = Coating not considered to be rework able.
DISCLAIMER: All values contained herein are typical
values. Please consult the Technical Data Sheet for the
specific product to obtain complete information and detailed
specification ranges and physical properties
|
|
Humiseal® Uv Curable Products
|
| HUMISEAL PRODUCT |
UV40 |
|
Mil-I-46058CIPC-CC-830 |
YES |
| UL Recognized |
YES |
| Solids Content (%
by weight)1 |
100 |
| Viscosity (centipoise) 2 |
800 |
| VOC (grams/liter )3 |
0 |
| Tack Free Time
(minutes) 4 |
N/A |
| Optical Brightener |
YES |
| Cure Type |
UV with
Moisture |
| Shelf Life (months) |
6 Months |
| Operating Temp.
Range °C |
-65 to
+125 |
| IR (teraohms) 5 |
800 |
| MIR (gigaohms) 6 |
60 |
| Dielectric Constant
7 |
2.5 |
| Dissipation Factor
8 |
0.01 |
| Ease of Rework 9 |
Moderate |
1 - Fed. Std. 141 Method 4044, 2 - Fed. Std. Method 4287
3 - Volatile Organic Compounds, 4 - Fed. Std. 141 Method
4061
5 - MIL-I-46058C, 6 - MIL-I-46058C
7 - ASTM D1 50 65T, 8 - ASTM D1 50 65T
9 - Very Easy = Can be easily removed by solvents or burn
through.
Easy = Not easily removed by solvents however can be removed
by Strippers, burn through or removed mechanically.
Moderate = Must be either mechanically removed or by using
special Strippers.
N/A = Coating not considered to be rework able.
DISCLAIMER: All values contained herein are typical
values. Please consult the Technical Data Sheet for the
specific product to obtain complete information and detailed
specification ranges and physical properties
|
|
Humiseal® Acrylics Resin Products
|
| HUMISEAL PRODUCT |
1B73
|
1B73
AP |
1B73
EPA |
1B73
LOC |
|
Mil-I-46058CIPC-CC-830 |
YES |
YES |
YES |
YES |
| UL Recognized |
YES |
YES |
YES |
YES |
| Solids Content (%
by weight)1 |
28.5 |
30 |
23 |
25 |
| Viscosity (centipoise) 2 |
250 |
400 |
230 |
455 |
| VOC (grams/liter )3 |
654 |
645 |
729 |
92 |
| Tack Free Time
(minutes) 4 |
30 |
25 |
30 |
25 |
| Optical Brightener |
YES |
YES |
YES |
YES |
| Cure Type |
Room or Elevated Temperature |
| Shelf Life (months) |
18 |
18 |
18 |
18 |
| Operating Temp.
Range °C |
-65 to
+125 |
| IR (teraohms) 5 |
550 |
550 |
550 |
550 |
| MIR (gigaohms) 6 |
70 |
70 |
70 |
70 |
| Dielectric Constant
7 |
2.6 |
2.6 |
2.6 |
2.6 |
| Dissipation Factor
8 |
0.01 |
0.01 |
0.01 |
0.01 |
| Ease of Rework 9 |
Very
Easy |
1 - Fed. Std. 141 Method 4044, 2 - Fed. Std. Method 4287
3 - Volatile Organic Compounds, 4 - Fed. Std. 141 Method
4061
5 - MIL-I-46058C, 6 - MIL-I-46058C
7 - ASTM D1 50 65T, 8 - ASTM D1 50 65T
9 - Very Easy = Can be easily removed by solvents or burn
through.
Easy = Not easily removed by solvents however can be removed
by Strippers, burn through or removed mechanically.
Moderate = Must be either mechanically removed or by using
special Strippers.
N/A = Coating not considered to be rework able.
DISCLAIMER: All values contained herein are typical
values. Please consult the Technical Data Sheet for the
specific product the specific product to obtain complete
information and detailed specification ranges and physical
properties
|
|
|
|
|
